Guides
3D Printing Infill Explained: How Much Do You Need?
What infill is, how infill percentage and pattern change strength, weight and cost, and how to choose the right setting for your FDM 3D print in Australia.
Laser 3D Print5 min read
On this page
When you look at a 3D printed part from the outside it looks solid, but most FDM prints are hollow on the inside, filled with a lightweight internal pattern called infill. Choosing how much infill to use is one of the simplest ways to balance strength, weight, print time and cost. This guide explains how infill works and how to pick a sensible setting for your next print.
What infill actually is
An FDM (fused deposition modelling) printer builds a part layer by layer from melted filament. Each layer has three main parts:
- Walls (perimeters): the outlines that form the outside skin of the part.
- Top and bottom layers: the solid surfaces that close the part off.
- Infill: the internal structure that fills the space between the walls.
Infill is expressed as a percentage. At 0% the inside is empty; at 100% it is completely solid. Most everyday prints sit somewhere in between, because a well-designed internal pattern gives plenty of support without wasting filament.
How infill percentage affects your print
Raising the infill makes a part stiffer and more resistant to crushing, but the gains taper off. Here is how the trade-offs generally look:
| Infill level | Typical use | Trade-off |
|---|---|---|
| Low (around 10–15%) | Display models, figurines, cosplay props, prototypes for fit | Light and quick, but not meant for heavy loads |
| Medium (around 20–40%) | General household items, brackets, enclosures, replacement parts | A good all-round balance of strength and cost |
| High (50% and up) | Parts that take repeated force, screw threads, tool handles | Heavier, slower and uses more filament |
These are starting points rather than fixed rules. The shape of the part, the material and the direction of the load all matter.
Walls often matter more than infill
A common surprise is that adding walls can strengthen a part more than adding infill. Bending and twisting forces mostly act on the outer skin, so a part with extra perimeters and moderate infill is often tougher than one with thin walls and dense infill. If a part needs to hold screws, survive drops or flex slightly, ask for more walls as well as, or instead of, higher infill.
Infill patterns in plain English
Slicer software offers several infill patterns. You don't need to know them all, but a few are worth recognising:
- Grid and lines: simple and fast, fine for light-duty parts.
- Gyroid: a wavy pattern that gives fairly even strength in every direction.
- Cubic and triangles: good general-purpose patterns for functional parts.
- Honeycomb: a classic hexagon pattern that is stiff but can be slower to print.
For most orders the pattern is a detail we handle for you. What helps us most is knowing what the part needs to do.
Matching infill to material
Infill works together with the filament you choose:
- PLA is stiff and easy to print, making it a great match for decorative pieces and prototypes at low to medium infill.
- ABS handles more heat than PLA, which suits parts that might sit in a hot car or near a warm appliance during an Australian summer. Medium infill with extra walls is a solid choice for functional ABS parts.
- Carbon fibre reinforced filament is stiffer again, so you can sometimes get the rigidity you need without going to very high infill.
If you're unsure which material suits your project, our guides on PLA vs ABS and carbon fibre 3D printing go into more detail.
How infill affects cost and turnaround
More infill means more filament and longer print times. Because our pricing is based on the weight of the finished part, infill has a direct effect on your quote. The instant quote calculator estimates weight from your part's dimensions assuming about 20% infill, which suits a wide range of everyday prints. If you want a denser or lighter part, mention it in your order notes and we'll confirm the final price after reviewing your file.
A few practical tips for keeping cost down without sacrificing strength:
- Use low infill for anything that is mainly decorative.
- Add walls rather than infill when a part needs to be tough.
- Design solid areas only where screws, pins or clips need them.
- Split very large parts so each piece prints efficiently within the 256 mm build volume.
What to tell us when you order
You don't have to be a slicer expert to get a well-printed part. When you request a print, a sentence or two in the notes is enough, for example "wall hook that holds a backpack" or "display figure, light as possible". We'll choose infill, walls and orientation to suit.
If you don't have a model yet, you can browse ready-made designs in Buy 3D Prints and have them printed and posted from Sydney.
Wrapping up
Infill is the hidden structure that decides how strong, heavy and costly a 3D print is. For most parts a moderate infill with sensible walls does the job, while decorative pieces can go lighter and hard-working parts denser. Tell us how your part will be used and we'll set it up accordingly.
Frequently asked questions
Is 100% infill the strongest option?
It is the most solid, but it is rarely the best choice. A fully solid FDM part is heavier, slower and costs more in filament, and for many parts extra walls add more useful strength than going from a moderate infill to solid. Tell us how the part is used and we can suggest a sensible balance.
Does infill change the price of a 3D print?
Yes. Our pricing is based on the weight of filament used, so more infill means more grams and a higher material cost. The instant quote calculator estimates weight assuming about 20% infill, and we confirm the final price after reviewing your file.
Can I choose the infill for my order?
Yes. Add your preferred infill, wall count or a short description of how the part will be used in the notes when you order, and we will set it up to suit before printing.
- #3D printing infill
- #infill percentage
- #FDM printing
- #print strength
- #Sydney
- #Australia
Ready to print your part?
Upload your STL, OBJ or 3MF and get an instant price. Printed in Sydney and shipped Australia-wide with flat-rate shipping.