Guides
How to Sand and Paint 3D Prints: A PLA Finishing Guide
A practical guide to sanding, priming and painting FDM 3D prints at home, from removing supports to hiding layer lines on PLA figurines and props.
Laser 3D Print5 min read
On this page
An FDM 3D print comes off the printer with fine layer lines and, depending on the shape, a few marks where supports touched it. For a functional bracket that rarely matters. For a figurine, bust, cosplay prop or display piece, a bit of sanding and paint turns it into something that looks finished rather than freshly printed. This guide walks through the process for PLA, the most common material for decorative prints.
What you need
You do not need a workshop. A basic kit from a hardware or hobby store covers most jobs:
- Flush cutters or a hobby knife for support removal
- Sandpaper in a range of grits, plus a sanding sponge for curves
- A small container of water for wet sanding
- Filler or spot putty for gaps and seams
- Spray primer suitable for plastics
- Acrylic paints and brushes, or spray paint for large areas
- A clear coat (matte, satin or gloss) to protect the finish
- A dust mask and a well-ventilated space, ideally outdoors
Always follow the safety directions on primers, fillers and spray cans, and avoid spraying in very humid or windy conditions, which can leave a rough or cloudy finish.
Step 1: Clean up supports and blemishes
Remove supports carefully with flush cutters, cutting close to the surface rather than tearing them off. Trim any leftover nubs with a sharp hobby knife, always cutting away from your hands. Small strings (thin wisps of filament) can be picked off or trimmed.
This is also the time to check for gaps between parts if the model was printed in pieces. Glue multi-part models together before you sand, so you can blend the seams in one go.
Step 2: Sand in stages
Sanding is where the layer lines disappear. Work through the grits rather than jumping straight to fine paper:
- Coarse grit removes support scars and the most obvious ridges.
- Medium grit smooths out the scratches left by the coarse paper.
- Fine grit, wet gives a smooth surface ready for primer.
Keep the paper moving and use light pressure. PLA softens with heat, and dry sanding in one spot can warm the surface enough to smear the plastic and clog the paper. Wet sanding at the finer grits avoids this and keeps dust down.
Be gentle around fine details such as faces, fingers and lettering. It is easy to sand away a crisp edge you wanted to keep. A sanding sponge or folded paper helps you get into curves without flattening them.
Step 3: Fill and prime
Spray a light coat of primer once the surface feels smooth. Primer acts like a magnifying glass: any layer lines, scratches or seams you missed will suddenly stand out. Mark them, apply a thin layer of filler or spot putty, let it dry, sand it back and prime again.
Two or three rounds of prime, fill and sand is normal for a display piece. Several thin coats always look better than one heavy coat, which can run and soften detail.
Step 4: Paint
Once the primer is smooth, you are ready for colour.
- Spray paint is fast and even for large single-colour areas, such as helmet shells or armour panels.
- Acrylic paint and brushes suit figurines and busts, where you want different colours and fine details.
- Washes and dry brushing bring out texture. A thin dark wash settles into recesses, then a light dry brush picks out raised edges.
Let each coat dry fully before handling or masking. Painter's tape helps keep clean lines between colours on props and signs.
Step 5: Seal the finish
A clear coat protects the paint from scratches and handling. Choose matte for a natural or stone-like look, satin for most figurines, or gloss for a shiny, polished finish. Apply it in light coats, just like the primer.
If the piece will sit in a sunny window or a hot car, remember that PLA can soften at fairly modest temperatures. Our PLA vs ABS guide explains what to consider for Australian heat.
Design choices that make finishing easier
A little planning before the print saves sanding later:
- Orient the model so visible surfaces are free of supports where possible.
- Split large or complex models into parts that print cleanly, then glue them.
- Avoid paper-thin details that will snap or vanish during sanding.
- Consider printing in a colour close to your final paint so chips are less visible.
Our FDM design tips cover orientation and supports in more depth. If you want colour without paint, a multicolour print can also be an option for simple designs.
Getting a print to finish
If you want a ready-made piece to practise on, browse Buy 3D Prints for physical prints shipped Australia-wide. If you have your own STL, OBJ or 3MF, use the instant quote calculator to price it in PLA, ABS or carbon fibre. And if you only have a picture or sketch, Convert 2D to 3D can turn it into a printable model first.
Frequently asked questions
Do I need to prime a 3D print before painting?
It is strongly recommended. A primer gives the paint something to grip, shows up layer lines and scratches you missed, and evens out the colour of the plastic underneath. Spray primers suited to plastics work well on PLA.
What sandpaper grit should I use on PLA?
Start coarse enough to knock down support marks and obvious ridges, then work up through finer grits. Many people begin somewhere around 120 to 220 and finish in the 400 to 800 range before priming. Wet sanding at the finer grits keeps PLA from heating up and clogging the paper.
Can I buy a print ready to paint?
Yes. Our Buy 3D Prints catalogue has physical FDM prints shipped Australia-wide, and you can sand and paint them yourself. If you have your own model, upload it for an instant quote instead.
- #painting 3D prints
- #sanding 3D prints
- #PLA finishing
- #layer lines
- #figurines
- #cosplay
- #Australia
Want a finished print, shipped?
Browse ready-to-ship physical 3D prints, printed in Sydney and delivered anywhere in Australia.