Design Tips
Designing for 3D Printing: 8 FDM Tips for Stronger Parts
Designing a part to 3D print? Eight practical FDM tips on overhangs, walls, holes, orientation and file prep so your print comes out strong and accurate.
Laser 3D Print5 min read
On this page
A good 3D print starts well before the printer warms up. The way a part is designed decides how strong it is, how accurate it is, and whether it needs messy support material. This guide covers eight practical tips for designing parts for FDM (filament) printing, the type of printing we do in our Sydney workshop. They apply whether you're modelling a replacement bracket in Tinkercad or a product prototype in Fusion.
How FDM printing builds a part
An FDM printer melts a plastic filament and lays it down one thin layer at a time, from the bottom up. Two things follow from that, and most of the tips below come back to them.
First, each layer needs something underneath it. A printer can't lay plastic onto thin air. Second, a part is strongest along its layers and weakest between them, a bit like the grain in timber. Design with those two facts in mind and you avoid most failed or fragile prints.
Tips 1 to 3: overhangs, bridges and supports
1. Keep overhangs to about 45 degrees. Each new layer can sit slightly past the one below it, so gentle angles print cleanly. A common rule of thumb is that anything up to about 45 degrees from vertical prints without help. Steeper overhangs droop or need supports.
2. Use chamfers instead of flat ceilings. A horizontal ledge sticking straight out is a classic support trap. Swapping it for a 45-degree chamfer, or turning a round hole on a vertical wall into a teardrop shape, often lets the part print with no supports at all.
3. Keep bridges short. A printer can stretch plastic across a gap between two supports, called a bridge, but long bridges sag. If you need a wide opening, add an arch or a central post, or design the part so the opening faces up.
Fewer supports means faster printing, less wasted material, and cleaner surfaces, since supports leave rough marks where they're removed.
Tips 4 and 5: walls, ribs and thickness
4. Don't make walls too thin. Very thin walls and tiny pins may print poorly or snap off. For a part that has to take load, a couple of millimetres is a sensible starting point, and thicker for anything that gets screwed, clamped or dropped.
5. Add ribs or fillets rather than bulk. A solid block uses a lot of plastic and can warp as it cools. Ribs, gussets and rounded inside corners (fillets) add stiffness where it's needed without making the part heavy. Since FDM pricing is usually based on weight, as we explain in our guide to what drives 3D printing cost, a lighter, well-ribbed design often costs less too.
Tip 6: orient the part for strength
Because layers are the weak point, think about which way the load runs. A long hook printed standing upright has its layers stacked across the bend, so it can snap along a layer line. The same hook printed lying flat runs the layers along its length and is much tougher.
Orientation also affects finish. The top and sides of a print usually look best, while the underside is flat against the bed. If one face matters for looks, mention it in your order notes so it can be printed facing up.
Tip 7: plan for fits and tolerances
Holes and slots on FDM prints often come out slightly smaller than drawn, and pegs a touch larger. If two printed parts slide together, or a bolt or bearing has to go in, leave a small clearance of a few tenths of a millimetre. For a critical fit, it's worth printing a small test piece first, or designing the hole slightly undersized and drilling it to the exact size afterwards.
Material matters here as well. ABS is a better pick than PLA for parts that face heat, like anything in a car during a Sydney summer, and carbon fibre filament adds stiffness for brackets and mounts. Our PLA vs PETG vs resin guide explains why heat resistance is such a big deal in Australia.
Tip 8: export a clean, correctly scaled file
Before you send a file:
- Check the units. Export in millimetres. A part designed in inches but read as millimetres comes out tiny.
- Check the size. Our printer's build volume is 256 x 256 x 256 mm. Anything larger needs to be split into sections that join after printing, ideally with pins or a dovetail for alignment.
- Make it watertight. The mesh should be a closed solid with no holes or overlapping surfaces. Most CAD programs export clean STL files; models from sculpting apps or downloads may need repairing.
- For multicolour, keep each colour as a separate body so it can be assigned its own filament.
STL is our preferred format, and 3MF and OBJ files are accepted too.
Ready to print your design?
Once your file is ready, run it through our instant quote calculator to get an estimate based on size, material and colours, then submit your file for review. Not a designer? Browse our ready-made 3D models, or if all you have is a photo, our Convert 2D to 3D service can turn it into a starting STL.
Frequently asked questions
Do I need supports for my 3D print?
Only if your design has steep overhangs or parts that float in mid-air. As a rule of thumb, FDM printers handle overhangs up to about 45 degrees from vertical without help. Steeper than that, the plastic needs support material underneath, which adds time and leaves marks where it's removed. Adding chamfers or angling features often removes the need for supports altogether.
Why did the holes in my print come out smaller than designed?
Holes on FDM prints commonly come out slightly undersized because of how the plastic is laid down around a curve. If a bolt, pin or bearing needs to fit, design the hole a few tenths of a millimetre larger than the part going into it, or plan to drill or ream it out to size afterwards.
What is the largest part you can print in one piece?
Our Bambu Lab P2S Combo has a build volume of 256 x 256 x 256 mm, so no single dimension can be more than 256 mm. Bigger designs can often be split into sections that are glued or bolted together after printing.
- #design for 3D printing
- #FDM design tips
- #STL file preparation
- #3D printing Sydney
- #functional parts
Ready to print your part?
Upload your STL, OBJ or 3MF and get an instant price. Printed in Sydney and shipped Australia-wide with flat-rate shipping.